Real-time control of sewer systems using turbidity measurements

Real-time control (RTC) of urban drainage systems has been proven useful as a means to reduce pollution by combined sewer overflow discharges. So far, RTC has been investigated mainly with a sole focus on water quantity aspects. However, as measurement techniques for pollution of wastewater are advancing, pollution-based RTC might be of increasing interest. For example, turbidity data sets from an extensive measurement programme in two Paris catchments allow a detailed investigation of the benefits of using pollution-based data for RTC. This paper exemplifies this, comparing pollution-based RTC with flow-based RTC. Results suggest that pollution-based RTC indeed has some potential, particularly when measurements of water-quality characteristics are readily available.     

An integral system‐ergonomic approach for IT‐based process management in complex work environments by example of manufacturing and health care

Recent trends in manufacturing and health care move these two work systems closer together from a system ergonomics point of view. Individual treatment of products, especially patients, by specialists in a distributed environment demand information technology (IT)‐based support suitable for complex systems. IT‐based support of processes in complex systems is difficult due to the lack of standard processes. IT support also means to rethink processes to use efficiency potentials. Close cooperation of users and software developers is needed to increase the ergonomic quality of the system. Therefore, suitable tools are needed: UML is available as the standard industry modeling language, Zope/Plone as the quasi‐standard for content management systems, SimPy as an object‐oriented simulation tool for event‐triggered processes, and ACT‐R as a powerful cognitive architecture for simulation of human information processes. The integration of these tools enables system‐ergonomic support of processes in the complex work system as well as of the development and deployment process. It is the base of an integral system‐ergonomic approach for IT‐based process management. Knowledge gained during process analysis either enters models or leads to the extension and adaptation of the tool chain. The models serve as basis for discussion among system ergonomists, programmers, and specialists from the work system. Further, they are understood by simulation and process support tools. Transcoding efforts between humans with different professional backgrounds and machines are reduced, and the flexibility demanded by complex systems is met. © 2008 Wiley Periodicals, Inc.     

Evaluation of a type 1 diabetes serum cohort by SELDI-TOF MS protein profiling

Proteomics analysis of serum from patients with type 1 diabetes (T1D) may lead to novel biomarkers for prediction of disease and for patient monitoring. However, the serum proteome is highly sensitive to sample processing and before proteomics biomarker research serum cohorts should preferably be examined for potential bias between sample groups. SELDI‐TOF MS protein profiling was used for preliminary evaluation of a biological‐bank with 766 serum samples from 270 patients with T1D, collected at 18 different paediatric centers representing 15 countries in Europe and Japan over 2 years (2000–2002). Samples collected 1 (n = 270), 6 (n = 248), and 12 (n = 248) months after T1D diagnosis were grouped across centers and compared. The serum protein profiles varied with collection site and day of analysis; however, markers of sample processing were not systematically different between samples collected at different times after diagnosis. Three members of the apolipoprotein family increased with time in patient serum collected 1, 6, and 12 months after diagnosis (ANOVA, p<0.001). These results support the use of this serum cohort for further proteomic studies and illustrate the potential of high‐throughput MALDI/SELDI‐TOF MS protein profiling for evaluation of serum cohorts before proteomics biomarker research.     

Spin dynamics and implications for superconductivity: some problems with thed-wave scenario

We review the spin dynamics of the normal state of the cuprates with special emphasis on neutron data in both the YBa₂Cu₃O_7– and La_2–x Sr _x CuO₄ systems. When realistic models of the Fermi surface shapes are incorporated, along with a moderate degree of spin fluctuations, we find good semiquantitative agreement with experiment for both cuprates. Building on the success of this Fermi-liquid-based scheme, we explore the implications ford-wave pairing from a number of vantage points. We conclude that our present experimental and theoretical understanding is inadequate to confirm or refute thed-wave scenario.     

Optical study of charge dynamics along thec-axis in high-Tc superconductors

Comparing the optical spectra withEc for typical high-T _c superconducting cuprates, we discuss the charge dynamics along thec-axis. The plasma energy or the mass anisotropic factorm _* ^c //m _* ^b is one of the key parameters determining the spectrum forEc. In Bi₂Sr₂CaCu₂O₈ and La_2–x Sr _x CuO₄ with a largem _* ^c /m _* ^b , the plasma energy is smaller than the superconducting gap energy, and thus the supercurrent along thec-axis is a kind of Josephson current flowing through insulating layers such as the BiO layers. On the other hand, in YBa₂Cu₃O₇ with a smallm _* ^c /m _* ^a , it seems that the coherent supercurrent flows along thec-axis. Although the spectrum forEc strongly depends on samples, presumably due to the difference in the hole concentration, a clear anisotropy between theab- and thec-directions is observed in the characteristics energy scales such as the plasma energy as well as the reflectivity knee energy.     

Phase-retardation and full-polarization analysis of soft-x-ray synchrotron radiation close to the carbon K edge by use of a multilayer transmission filter

We have produced a multilayer transmission filter with 100 periods of Cr/C to achieve a significant phase retardation while maintaining good transmission for photon energies just below the carbon K edge. This device was installed into a polarimeter behind the SX700/3 monochromator at the Berlin synchrotron radiation laboratory, BESSY. The phase-retardation properties were observed as theoretically predicted. Agreement between experiment and calculation could be obtained by introduction of a rather small interface roughness in the simulation code (σ = 0.65 nm rms). An observed phase retardation of 5° was sufficient to permit, for the first time we believe, a complete and unambiguous polarization analysis of soft-x-ray synchrotron radiation (265-eV photon energy) with primary standards.     

Optical properties of broadband reflection holograms

The optical properties of highly chirped gratings of broadband reflection-type volume phase holograms are evaluated by a ray-tracing approach. The deformation of the fringes as well as the change of refractive index is attributed to swelling during processing. For high-efficiency holograms the problem can be reduced to geometric optics. The power density distribution in the focus of an on-axis mirror is calculated by a Monte Carlo integration. The results are discussed for replay conditions that are relevant for photovoltaic applications.     

A Novel Magnetic Hardening Mechanism for Nd-Fe-B Permanent Magnets Based on Solid-State Phase Transformation

Permanent magnets based on neodymium-iron-boron (Nd-Fe-B) alloys provide the highest performance and energy density, finding usage in many high-tech applications. Their magnetic performance relies on the intrinsic properties of the hard-magnetic Nd₂Fe₁₄B phase combined with control over the microstructure during production. In this study, a novel magnetic hardening mechanism is described in such materials based on a solid-state phase transformation. Using modified Nd-Fe-B alloys of the type Nd₁₆Fe_bal-x-y-zCo_xMo_yCu_zB₇ for the first time it is revealed how the microstructural transformation from the metastable Nd₂Fe₁₇B_x phase to the hard-magnetic Nd₂Fe₁₄B phase can be thermally controlled, leading to an astonishing increase in coercivity from ≈200 kAm⁻¹ to almost 700 kAm⁻¹. Furthermore, after thermally treating a quenched sample of Nd₁₆Fe₅₆Co₂₀Mo₂Cu₂B₇, the presence of Mo leads to the formation of fine FeMo₂B₂ precipitates, in the range from micrometers down to a few nanometers. These precipitates are responsible for the refinement of the Nd₂Fe₁₄B grains and so for the high coercivity. This mechanism can be incorporated into existing manufacturing processes and can prove to be applicable to novel fabrication routes for Nd-Fe-B magnets, such as additive manufacturing.     

A Synthetic Dynamic Polyvinyl Alcohol Photoresin for Fast Volumetric Bioprinting of Functional Ultrasoft Hydrogel Constructs

Tomographic volumetric bioprinting (VBP) enables fast photofabrication of cell-laden hydrogel constructs in one step, addressing the limitations of conventional layer-by-layer additive manufacturing. However, existing biomaterials that fulfill the physicochemical requirements of VBP are limited to gelatin-based photoresins of high polymer concentrations. The printed microenvironments are predominantly static and stiff, lacking sufficient capacity to support 3D cell growth. Here a dynamic resin based on thiol–ene photo-clickable polyvinyl alcohol (PVA) and thermo-sensitive sacrificial gelatin for fast VBP of functional ultrasoft cell-laden hydrogel constructs within 7–15 s is reported. Using gelatin allows VBP of permissive hydrogels with low PVA contents of 1.5%, providing a stress-relaxing environment for fast cell spreading, 3D osteogenic differentiation of embedded human mesenchymal stem cells and matrix mineralization. Additionally, site-specific immobilization of molecules-of-interest inside a PVA hydrogel is achieved by 3D tomographic thiol–ene photopatterning. This technique may enable spatiotemporal control of cell-material interactions and guides in vitro tissue formation using programmed cell-friendly light. Altogether, this study introduces a synthetic dynamic photoresin enabling fast VBP of functional ultrasoft hydrogel constructs with well-defined physicochemical properties and high efficiency.